How to Season a Carbon Steel Pan

A pat of butter melting in The Original carbon steel skillet on a gas burner

To season a carbon steel pan, wipe on a very thin coat of high-smoke-point oil like canola, vegetable oil, grapeseed or Crisco, wipe most of it back off, and heat the pan until it stops smoking. Do that a few times, then keep cooking with it, because cooking builds seasoning better than anything else. Our skillets come pre-seasoned, so you can cook on one the day it arrives.

What Seasoning Is

Seasoning is cooking oil that has been heated past its smoke point until it bonds to the steel as a hard, dark layer. Every time you cook with fat, a little more builds on top of what's there, which is why a carbon steel pan gets slicker the more you use it. Unlike a nonstick coating, it can always be touched up or rebuilt, so the pan never wears out the way a coated pan does.

Do You Need to Season a New Pan?

Some carbon steel pans ship as bare gray steel and need several rounds of seasoning before the first cook. Ours don't. Every Texas Pan Company skillet is seasoned in our shop before it ships, so all you need to do is rinse it, dry it, heat it up with some oil or fat, and start cooking.

How to Season on the Stovetop

This is the quick touch-up we use when a pan has been scrubbed hard, had rust taken off, or just looks dry.

1. Clean and dry the pan

Wash it, towel it off, and set it on the burner over medium heat for a minute so every bit of water is gone, including around the rivets.

2. Wipe on a very thin coat of oil

Put a little high-smoke-point oil on a paper towel and rub it over the cooking surface, then take a clean paper towel and wipe most of it back off. It should look almost dry. Too much oil is what makes seasoning sticky.

3. Heat it until it stops smoking

Leave the pan over medium to medium-high heat. The oil will smoke for a bit, and when the smoke dies down, that layer has bonded. Turn off the heat and let it cool.

How to Season in the Oven

If a big part of the pan is down to bare steel, after a bad rust spot or a full strip, an oven seasoning builds an even base faster.

  1. Wipe a very thin coat of high-smoke-point oil over the whole pan, inside and out, and wipe off the excess.
  2. Set it upside down in the oven at 450 to 500°F for an hour.
  3. Turn the oven off and let the pan cool inside it.
  4. Repeat two or three times.

Which Oil to Use

For seasoning layers, use a high-smoke-point oil: canola, vegetable oil, grapeseed or Crisco all work, and you don't need anything expensive. Skip olive oil and butter for this part, since they smoke at lower temperatures and don't build as hard a layer. Our Carbon Steel Seasoning tin works too, and you use it exactly the same way as any other oil.

When you're just cooking, any fat helps. Bacon grease, tallow, butter and oil all add a little to the seasoning over time.

When to Re-Season

Carbon steel almost never needs to be stripped and started over. Do a quick stovetop round when food starts sticking more than usual, when you see gray steel showing, after you've scrubbed hard or cooked something acidic, or after you've taken off rust (our rust guide walks through that). The rest of the time, cooking regularly keeps it in shape.

Why It Looks Patchy

A carbon steel pan isn't supposed to be one even shade of black. Black, brown and bronze patches are just seasoning building up in layers, and spots you've scrubbed will look lighter until they catch up. A pan that looks used is a pan that's working.

Why It's Sticky

Sticky seasoning almost always means too much oil went on at once. Heat the pan and wipe off what you can, and if it's still tacky, scrub that spot and season it again with much less oil.

Soap, Acid and Everyday Care

A little dish soap won't hurt seasoning that has bonded. What matters is drying the pan completely, because water left on the steel is what causes rust. Our routine is wash, towel dry, a minute on the burner, then a thin coat of oil while it's warm, and never soaking it, leaving it in the sink or putting it in the dishwasher.

Acidic foods like tomato sauce, wine, vinegar and citrus can wear seasoning thin, especially on a newer pan. A splash of lemon won't do any harm, but we'd hold off on simmering tomato sauce for an hour until the pan has some miles on it. If seasoning does come off, clean the spot and add another layer.

What to Cook First

For the first couple of weeks, cook things with some fat in them: bacon, burgers, steak, potatoes in oil, onions in butter or grease. Wait on eggs, fish and tomato sauce until the seasoning has built up. Some early sticking is normal, and it gets better every time you cook.

Carbon Steel Seasoning FAQs

How do you prepare a new carbon steel pan?

If it arrives as bare gray steel, wash off the protective oil or wax it shipped with, dry it on the burner, and give it two or three oven seasoning rounds. A pre-seasoned pan like ours only needs a rinse, a dry and a little oil before the first cook.

How many times should I season a new carbon steel pan?

A bare steel pan needs two or three thin oven layers to start. Ours arrive pre-seasoned, so you can skip that and just cook.

Does carbon steel get more nonstick over time?

Yes. As seasoning builds and you get a feel for the heat, food releases more easily.

Can seasoning come off?

Yes, from hard scrubbing, acidic food or overheating, but the steel underneath is fine. Clean the spot, dry it and season it again.

Should I oil my pan after every use?

We do. A very thin coat after drying protects the steel, especially if you live somewhere humid or won't use the pan for a while.

Can I cook eggs in carbon steel?

Yes, once the seasoning has built up. Preheat the pan, use butter or oil, and give the eggs a moment to set before you move them.